JNTU-K B.TECH R19 3-1 Syllabus For Micro processors and micro controllers PDF 2022
January 31, 2022 2022-01-31 13:54JNTU-K B.TECH R19 3-1 Syllabus For Micro processors and micro controllers PDF 2022
JNTU-K B.TECH R19 3-1 Syllabus For Micro processors and micro controllers PDF 2022
Get Complete Lecture Notes for Micro processors and micro controllers on Cynohub APP
Download the APP Now! ( Click Here )
You will be able to find information about Micro processors and micro controllers along with its Course Objectives and Course outcomes and also a list of textbook and reference books in this blog.You will get to learn a lot of new stuff and resolve a lot of questions you may have regarding Micro processors and micro controllers after reading this blog. Micro processors and micro controllers has 5 units altogether and you will be able to find notes for every unit on the CynoHub app. Micro processors and micro controllers can be learnt easily as long as you have a well planned study schedule and practice all the previous question papers, which are also available on the CynoHub app.
All of the Topic and subtopics related to Micro processors and micro controllers are mentioned below in detail. If you are having a hard time understanding Micro processors and micro controllers or any other Engineering Subject of any semester or year then please watch the video lectures on the official CynoHub app as it has detailed explanations of each and every topic making your engineering experience easy and fun.
Micro processors and micro controllers Unit One
8086/8088 MICROPROCESSORS
Register organization of 8086, Architecture, signal description of 8086, physical memory organization, general bus operation, I/O addressing capability, special purpose activities, Minimum mode, maximum mode of 8086 system and timings, the processor 8088, machine language instruction formats, addressing mode of 8086, instruction set off 8086,assembler directives and operators.
Micro processors and micro controllers Unit Two
PROGRAMMING WITH 8086 MICROPROCESSOR
Machine level programs, programming with an assembler, Assembly language programs, introduction to stack, stack structure of 8086/8088, interrupts and interrupt service routines, interrupt cycle of 8086, non-mask able interrupt and mask able interrupts, interrupt programming.
Get Complete Lecture Notes for Micro processors and micro controllers on Cynohub APP
Download the APP Now! ( Click Here )
Micro processors and micro controllers Unit Three
BASIC AND SPECIAL PURPOSE PROGRAMMABLE PERIPHERALS AND THEIR INTERFACING WITH 8086/88
88Semiconductor memory interfacing, dynamic RAM interfacing, interfacing i/o ports, PIO 8255 modes of operation of 8255,interfacing to D/A and A/D converters, stepper motor interfacing, control of high power devices using 8255.Programmable interrupt controller 8259A, the keyboard /display controller8279, programmable communication interface 8251 USART, DMA Controller 8257.
Micro processors and micro controllers Unit Four
8051 MICROCONTROLLER
Introduction to microcontrollers, 8051Microcontrollers, 8051pin description, connections, I/O ports and memory organization, MCS51addressing modes and instructions, assembly language programming tools.
Micro processors and micro controllers Unit Five
PIC MICROCONTROLLERS AND ARM 32-BIT MICROCONTROLLER
Overview and features, PIC16Cx/7X instructions, interrupts in PIC 16C61/71, PIC 16F8XX Flash controllers, I/O ports and timers. Introduction to 16/32 Bit processors, ARM architecture and organization, ARM / Thumb programming model, ARM / Thumb instruction set.
Micro processors and micro controllers Course Objectives
The student will
learn concepts of microprocessor, different addressing modes and programming of 8086.
understand interfacing of 8086, with memory and other peripherals.
learn concept of DMA, USART RS-232 and PIC controller.
study the features of advanced processors and Pentium processors.
study the features of 8051 Microcontroller, its instruction set andalso other controllers.
Micro processors and micro controllers Course Outcomes
After going through this course the student will be able to develop programs for different addressing modes.
perform 8086 interfacing with different peripherals and implement programs
describe the key features of serial and parallel communication and able to
Design a microcontroller for simple applications.
Micro processors and micro controllers Text Books
1.A.K.Ray, K.M.Bhurchandi ,”Advanced Microprocessors and Peripherals”, Tata McGraw Hill Publications,2000.
2.N.Sentil Kumar, M.Saravanan, S.Jeevananthan, “Microprocessors and Microcontrollers”, Oxford University Press,2010.
Micro processors and micro controllers Reference Books
1.Ajay V Deshmukh, ”Microcontrollers”, TATA McGraw Hill publications,2012.
2.Krishna Kant, “Microprocessors and Microcontrollers”, PHI Publications, 2010.
Scoring Marks in Micro processors and micro controllers
Scoring a really good grade in Micro processors and micro controllers is a difficult task indeed and CynoHub is here to help!. Please watch the video below and find out how to get 1st rank in your B.tech examinations . This video will also inform students on how to score high grades in Micro processors and micro controllers. There are a lot of reasons for getting a bad score in your Micro processors and micro controllers exam and this video will help you rectify your mistakes and help you improve your grades.
Information about JNTU-K B.Tech R19 Micro processors and micro controllers was provided in detail in this article. To know more about the syllabus of other Engineering Subjects of JNTUH check out the official CynoHub application. Click below to download the CynoHub application.